MATEK ELRS-R24-V R24V ELRS 2.4G 7CH PWM VARIO RECEIVER Variometer Sensor With CRSF-PWM-V CONVERTER for RC Gliders Fixed-Wings

filler

Price:
$28.94

ELRS-R24-V
  • Specific for the Gliders and other fixed-wings.  Small in form factor, It can be installed in gliders with restricted payload bays such as DLG's and high performance slopers. Not needing to install an additional altimeter/variometer also saves room and weight.

  • The built in barometer provides vertical speed telemetry. The variometer sounds both ascending and descending tones, so you will know whether you are in lift or sink without having to look at your transmitter.

  • with ExpressLRS firmware and CRSF protocol, this will also give you other telemetry data like battery voltage, current and GPS related.

Specifications

  • ESP8285, SX1281, ExpressLRS Firmware

  • RF Frequency: 2.4GHz ISM (2400~2480MHz)

  • Antenna connector: IPEX MHF-1

  • Telemetry power: 12dbm

  • CRSF-PWM-V converter with barometer integrated

  • 7x PWM outputs (frequency 50~400Hz)

  • 1x UART(2) for GPS

  • 36V Max. battery voltage sense (1K:10K voltage divider built-in)

  • Compatible with external Current sensor (0~3.3V)

  • RxBt,Curr,Capa,Bat%,GPS telemetry and VSpd(Vario)

  • Rated voltage: 3.5~9V @5V pad, 0~36V @Vbat, 0~3.3V @Curr

  • Power dissipation:  50mA(binding), 90mA(wifi mode)

  • No 5V regulator built-in

  • Failsafe value configurable

  • Firmware upgradeable

  • Physical:
    • PCB Size: 27x16mm,

    • Weight: 5g w/ antenna and 2.54 pins

  • Packing:
    • 1x  ELRS-R24-V(includes CRSF-PWM-V and 2.4G Receiver)

    • 1x IPEX MHF1 Antenna

    • 2.54mm straight and 90° 3×6 Dupont pins

Firmwares

  • 2.4GHz Receiver: ExpressLRS /DIY_2400_RX_ESP8285_SX1280,  V2.0 or newer

  • CRSF-PWM-V: crsf_pwm_v2.0 or newer

CRSF-PWM-V

Pinouts and Pads

  • Tx1/Rx1(UART1) for Receiver integrated

  • Tx2/Rx2(UART2) for GPS/firmware update/setting parameters

  • 1~8: CH1~CH8 PWM outputs

  • Curr: current sensor signal (0~3.3V)

  • Vbat: 0~36V Battery voltage sensing

  • G: ground

  • 4v5 pad voltage = 5V pad voltage -0.3V.

  • no 5V regulator built-in, need to power on the board and receiver via external 5V source

Failsafe (FW 2.0.0 or newer)

  • CH3 is arranged for the throttle,  Failsafe value = 988 by default.  you can change the failsafe value of CH3 and other channels by following settings.

  • Make sure ESC signal is disconnected from CRSF-PWM board before starting failsafe settings

  • Bridge PWM1 and PWM2 signal pad, then power on CRSF-PWM board and receiver.

  • Failsafe value will be saved automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.

  • Failsafe value = The PWM value of each transmitter channel when CRSF signal is received by CRSF-PWM board.

  • Remove the jumper between PWM 1 and 2,  then CRSF-PWM board will work in normal PWM output mode.

LED status

  • slow blinks: CRSF-PWM board doesn't receive CRSF signal, e.g., receiver is not bound with transmitter.

  • solid ON:  CRSF-PWM board and receiver are working normally

  • 5x fast blinks after powering on for 10 seconds: CLI mode is active

GPS telemetry

  • Compatible with GPS NMEA protocol, 1Hz, Baud 9600~115200

  • GPS "TX" to CRSF-PWM board "RX" Single wire half duplex UART connection,   CRSF-PWM board "TX" to GPS "RX" is not essential.

  • Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats

  • u-blox series GPS can output "0+1 – UBX+NMEA" protocol by default

  • Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.

  • Troubleshooting for no GPS telemetry,  double check the wiring between GPS and CRSF-PWM board,  some u-blox GPS may don't output NMEA protcol, you need to revert GPS to default configuration in u-center.

  • with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.

VSpd telemetry

  • Barometer SPL06-001 (I2C address 0x76) integrated

  • VSpd telemetry is supported by ExpressLRS 2.0, EDGE 2.6, OPENTX 2.2 or newer.

TIM & PWM Frequency

  • PWM frequency on all 10x Channels can be configured according to TIM

  • PWM run at 50Hz by default

  • TIM2:  CH1, CH2, CH4

  • TIM16: CH3

  • TIM3:  CH5, CH6, CH7, CH8

CLI mode

  • If CRSF-PWM board doesn't detect GPS connected to UART2 within 10 seconds after powering on,  CLI mode will active.

  • After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.

  • in CLI mode, CRSF-PWM board firmware can be updated

  • CLI mode has no effect to receiver CRSF signal and PWM outputs


Payment & Security

American Express Apple Pay Diners Club Discover Meta Pay Google Pay Mastercard PayPal Shop Pay Venmo Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently viewed