BOB57 Cinematic LR & Freestyle 6inch 6S BNF with Nebula Pro Vista HD System for FPV

• The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

Features:

• 6 inch drone re-engineered: This drone was specifically designed for 6 inch

• H-shaped frame with robust middle section for less props in view while remaining stiffness

• XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.

• Built in BEC to directly power a gopro (no battery needed)

• Hybrid motor design: This motor is optimized for 6 inch.  Can be used with bi- blades (efficiency) and tri-blades (agility & trust). 

• Antenna mount: Solid antenna mount for less ocillations when using long antennas

• Long back bone: Enough space up to 3000mAh 6S batteries

• Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)

• GPS: A high-end GPS is used to minimize the risk of failure during proximity flights 

• ESC: The drone consists iFlight's new ESCs with built-in spike absober for more reliability

• Pre-Tune by Ellisvanjason

• 9min flight time with 1800mAh 6S

• 9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

Specifications:

• Upper(middle) plate thickness: 2.5mm

• Bottom plate thickness: 1.5mm 

• Total Dimensions: 254*254mm 

• Bottom to top distance: 22mm 

• Geometry: H-shaped frame

• Top plate thickness: 2mm 

• Ellisvanjason 2506 motors 

• Gemfan 6032 propellers

• Arm Thickness: 6mm

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC):

FC //BLITZ F722 Flight Controller

• Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter

• Smartaudio / IRC Tramp VTX protocol supported

• Firmware target: IFLIGHT_BLITZ_F722

• Motor outputs: 4x (SH1.0 connector)

• Flash: 32MB (Blackbox flash)

• I2C serial: SDA / SLA pads

• Dimensions: 36.5*35 mm

• Barometer: DPS310

• OSD Chip: AT7456E

• LED controller: Yes

• MCU: STM32 F722

• Beeper pad: Yes

• Gyro: BMI270

• Weight: 7.8g

• UARTS: 6

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

• Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

• Mounting Holes: 30.5*30.5mm/Φ4mm

• Target:   IFLIGHT_BLITZ_G2

• Supports 2-6S Lipo input

• Current sensor: Yes

• Constant: 55 Amps 

• Current rate: 200

• Burst: 65 Amps

• Weight: 15.3g

• MCU: G071

• BEC: No

Note:

• All iFlight BNFs are tested before shipment to guarantee the highest quality. 

• If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

• iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.