Skip to product information
1 of 8

SoloGood.RC

BETAFPV F4 1S 12A V2.0 AIO Brushless FC Flight Controller Support Frsky Receiver/ Futaba Receiver

BETAFPV F4 1S 12A V2.0 AIO Brushless FC Flight Controller Support Frsky Receiver/ Futaba Receiver

Regular price $36.40 USD
Regular price Sale price $36.40 USD
Sale Sold out
Color
 

What is updated in ELRS 2.4G V2.0?

• Now supports 1S and 2S batteries; version 1.0 only supports 1S.

• Use SPI ExpressLRS 2.4 receiver with BetaLight firmware.

• Modify the shape of the motherboard to support 85mm whoop rack; V1.0 version only supports toothpick machines.

• Use a lighter and smaller SH interface connector instead of USB Type-C.



F4 1S 12A AIO flight controller-a 1S 12A FC, used to assemble a light 3-inch toothpick machine, such as HX115 LR voyage through machine. If you want to try a FPV drone larger than 65mm/75mm with 1S power, you still want to For smooth and powerful flight movements, this integrated 1S 12A ESC flight controller is your best choice.


F4 1S 12A AIO Flight Controller is a better choice to build an ultra-lightweight 3-inch toothpick machine, such as HX115 LR
At present, most of the 1S flight controllers on the market have their own 5A ESCs, but this FC specifically integrates 1S 12A ESCs, which can provide more sufficient power for the 3-inch toothpick machine.
Built-in ammeter, 2 programmable RGB LEDs and SPI Frsky receiver. At the same time, all the pads are reserved for external receivers with UART1 and UART2 for buzzer and so on.
The Whoop mounting hole pattern is compatible with most 1S 3-inch racks. Large pads are reserved for welding motor cables. This design will make welding easier.
Product parameter

Flight control: F4 1S 12A AIO FC (Frsky)
Weight: 4.74 g (excluding power cord and BT2.0 connector)
CPU: STM32F411CEU6 (100MHZ)
Gyroscope: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
OSD: Built-in BetaFlight OSD (STM32 controls the OSD chip through SPI in DMA mode)
Receiver: Integrated SPI Frsky receiver / Futaba receiver
Motor pin connector: 1.25mm pin header
Mounting hole size: 26mm x 26mm (suitable for speaker pattern mounting holes)
USB port: Type-C
1S 12A ESC specifications
Built-in ESC, continuous 12A, peak 25A current
Input voltage: 1S Lipo
ESC firmware: Z_H_30_REV16_7.HEX
Signal support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM


This new BLHeli_S firmware (named Z_H_30_REV16_7.HEX) is supported by BLHeli Configurator, BLHeliSuite and Bluejay Configurator.

F4 1S 12A AIO FC schematic diagram
The following figure shows the wiring diagram of ELRS 2.4G version. The UART1, UART2 and SBUS pads are used for external receivers, such as Frsky XM+, TBS Nano receivers, in order to provide a longer receiver range.

The buzzer pads (BUZZ+ and BUZZ-) are directly invalid. Some modifications are required to make it work.

The picture below shows the ELRS 2.4G V1.0 motherboard


The picture below shows the ELRS 2.4G V2.0 motherboard


The ammeter is integrated on the FC board. This is the configuration in Betaflight Configurator.

12A 1S ESC
Does 1S UAV really need 12A ESC? If it is a 65mm or 75mm Whoop drone Meteor65, 5A ESC is sufficient for all actions. How about a 3-inch propeller with a 1102/1202.5 motor? Still want a smooth and powerful flight maneuvers?

The 5A ESC was developed about 3 years ago and is designed for drones equipped with 0603/0802 motors. In the past year, the BETAFPV team has been cooperating with BLHeli author Steffen to develop the 12A 1S ESC for the 3-inch toothpick machine. Finally, it's here!


The board is marked with "1-2S", can this FC board support 2S?

The V1.0 board does not support 2S batteries. Please select V2.0 motherboard to support 1S and 2S batteries.

ELRS 2.4G RX
The board integrates the receiver with ExpressLRS, a radio link popular in 2021. ExpressLRS is designed to achieve better link performance in terms of speed, latency and range. The serial protocol between the receiver and F411 FC is the Crossfire serial protocol.


This circuit board is specially designed for long-range 3 inch ultralight toothpick drone or 2Swhoop drone.

If you want to try ExpressLRS on 65mm/75mmwhoop drones, please continue to pay attention to our F4 1S FC board, which has a built-in SPI ExpressLRS receiver.

 

Product List

1 * F4 1S 12A all-in-one
4 * Shockproof rubber damping column
4 * M2 x 10mm screws
4 * M2 x 10mm screws
8*M2 screw nut
1 * BETAFPV dipole T-type antenna (2.4G/46mm, only for ELRS RX flight control)
8 * PH-1.25 motor connector (not welded, only for ELRS RX flight control)

 

Ingredients

Nutritional info

Shipping

View full details

Image with text

Pair text with an image to focus on your chosen product, collection, or blog post. Add details on availability, style, or even provide a review.